DIY Concrete Succulent Planter With Tiny Wooden Legs and Lace Trim

January 28, 2022 Post a Comment

Isn't this trivial succulent planter merely adorable? Information technology looks like a miniature table with cute stubby legs and it's made of concrete and woods. What'south cool about it is that it's a DIY succulent planter that y'all tin make from scratch. Likewise, you can customize information technology in lots of different ways and requite it whatsoever shape you desire or potentially get in bigger.

Concrete succulent planter

Materials needed for this concrete succulent planter:

concrete mix
water
basin
spoon
rule
blackness mark
pencil
handsaw
square wooden dowel
pigment castor
light-green acrylic paint
box cutter/ 10-acto pocketknife
scissors
tape
box

How to make the delicious planter:

Step 1: Measure the mark an outline on the box

You can use any empty cardboard box for this since all you need information technology for is to make a mold to pour the concrete into. An orangish juice box would do merely fine and is actually perfect since information technology has a square-shaped bottom. Use a ruler to measure out how tall you want the mold to be and make a marking with a sharpie.

Trace a direct line on one side of the box marking where yous want to make the cutting and and then flip the box over and exercise the same thing on all iv sides. Make sure your marks line up.

Related: How To Create And Care For Your Stunning Succulent Arrangements

Information technology'south easy to do this if you just make a mark on one side, then move the ruler and make a second mark and and then describe a directly line that goes through both of them.

Footstep ii: Cutting forth the line

Apply a pair of scissors, a box cutter or an 10-acto pocketknife to cut forth the lines yous've just made. Basically you demand to cutting off the bottom of the box so y'all can use information technology as a mold. Of course, if you already have a small disposable box that has just the right shape and size you tin completely skip this part and utilize that instead.

Step three: Cut out four dowel pieces

Y'all should have a square wooden dowel ready to go for this project. Take it and utilise the ruler and a pencil to marker the point where you want to cut it in order to make four footling legs for your succulent planter.

Depict lines on all four sides of the dowel with your pencil so you have a sort of guide when you're cutting the dowel.

Step 4: Make the cuts

Yous'll need to use your handsaw for this role. Make cuts along the pencil lines that you've fabricated earlier. Don't feel like y'all need to split the dowel into four pieces just so you utilise all of it. It's ok to have some leftovers. Perhaps you can utilize that for a different project.

Step 5: Paint the tiny dowel legs

Side by side take your acrylic pigment and paint brush and utilise them to make the little dowel legs look nice and colorful. Paint the 4 dowel pieces on all sides including ane of the ends. The other 1 tin be left exposed since it won't be visible.

Step 6: Draw an outline of the legs in the four corners on the box

Have the painted legs and position one in each of the four corners of the cardboard box mould you've prepared earlier. Use a black sharpie to make an outline around them.

Step 7: Cut out four piffling squares in the corners of the box

Following the outlines, cut out four fiddling squares in the corners of the mould. You should use an x-acto knife for this since it'south precise and easy to utilize. A box cutter would also work only fine.

Stride 8: Push button the legs through the holes

At present that you lot've fabricated these little foursquare holes in the mold, take the iv niggling dowel legs and button them through these holes. Don't push them all the way through. Just make certain they're level when all take been inserted.

Step 9: Put tape around the box

Y'all can pretty much utilise any kind of tape for this. The thought is to reinforce the box and then it retains its shape when you lot cascade the physical in it. That way the concrete succulent planter volition have nice and straight edges.

Step x: Mix the physical

Mix the physical with the water in a bowl using a spoon until yous get a smooth paste. Both the bowl and the spoon should be disposable then don'tuse whatsoever that you lot're going to miss considering you'll have to throw them out when yous're done with this project.

Pace xi: Pour the concrete mixture into the mold

When you're happy with the consistency of your concrete mixture, cascade information technology into the mold. Fill the mould almost all the way upwards and get a dainty and flat surface at the meridian.

Step 12: Insert a plastic loving cup in the middle of the mould

Have a dispensable plastic loving cup and push into the concrete in the heart of the mould. This volition create a pigsty when the concrete dries out where you can plant your footling succulents.Fill the cup with some rocks or something heavy so it stays in place.

Footstep xiii: Remove the mould

Wait for the concrete to dry out, preferably overnight. Then go ahead and remove the mould. Y'all tin cut it and pare it off fairly easily.

Step 14: Paint the planter

Utilize a bit more of the acrylic paint to now paint the outside of the concrete succulent planter. You can pigment the whole thing or just make a trim around the bottom.

Pace 15: Decorate the planter with lace ribbon

Let the paint dry and then take some lace ribbon and add a trim effectually the planter. Use your hot glue gun to adhere the lace and to make certain it stays in place.

Footstep 16: Paint the top of the planter

The final footstep is to paint the meridian portion of the planter. There's no need to paint the eye since you'll be filling it with soil and succulents anyway. Once this is washed, let the paint dry for a bit then you tin can go ahead and add the fiddling plants.